Data quality and uncertainty assessment methodology for pavement LCA

In performing pavement life cycle assessment (LCA), users are facing various reports of energy intensity coefficient (EIC) of pavement materials which differ considerably among data sources and therefore alter the LCA results significantly. Instead of selecting a certain EIC without or of little explanation for the current pavement LCA practices, this study proposed a methodology to build probability density function (PDF) for EIC based on available data-set and their qualities. Each data was first evaluated about the data quality indicator (DQI) through data quality pedigree matrix and converted to PDF in modified Beta distribution form. Three weighting methods, the DQI one, coefficient of variation (COV) one and analytical hierarchy process (AHP) one, were developed to assign weightings for different data. Monte Carlo simulation was run with the weighted PDF of each data as input to obtain the ultimate PDF for EIC. A case study to estimate the bitumen’s EIC with eight data samples were performed using the proposed methodology. It is found (1): the estimates by the proposed methodology is of higher reliability (lower COV) compared to any single data due to utilisation of information of the overall data samples; (2) the AHP weighting method is most favoured despite the results of the three weighting methods are close; (3) the central estimates of bitumen’s EIC are between5.4~5.8 MJ/kg. The proposed methodology is helpful in aiding calculating EICs for pavement materials and capturing uncertainties in LCA results in a statistical sense.     

Fabrication and mechanical properties of large-scale SiC impeller via vacuum gelcasting and pressureless sintering

Impeller is the key part of centrifugal pump to convey liquid. And combined with the engineering practice, we fabricated two types of open and semi-open SiC ceramic impellers with diameter of 100 mm and 160 mm via gelcasting and pressureless sintering. B4C and C were used as the sintering additives and sprayed drying granulation method was adopted for the starting SiC powder processing. Given the size and shape complexity of impeller, the optimized pH value, dispersant content, and solid-loading content for the fabrication of the SiC impellers were determined to be 10-11, 0.8 wt%, and 40 vol%, respectively. For the open impeller, blade height, cover board thickness, drying shrinkage, and sintering shrinkage are 10.5 mm, 4 mm, 10.3%, and 21.3%, respectively. For the semi-open ones, the corresponding parameters are 41 mm, 10 mm, 10.3%, and 21.3%, respectively. The average density of the two types of impellers is 3.15 g/cm3, and the mechanical properties of both impellers, including average hardness, flexural strength, compressive strength, and fracture toughness are 2478 HV, 436 MPa, 2093 MPa, and 3.17 MPa·m1/2, respectively. All variation coefficient values are smaller than 5%, which indicates a good uniformity in densities and mechanical properties of both the impellers.     

退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响

采用显微组织分析和分子动力学模拟等方法研究了退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响。结果发现,晶粒尺寸随温度的升高逐渐增加并趋于稳定,但是断后伸长率和断面收缩率在950 ℃突然大幅度下降。试样组织形貌在800 ℃和950 ℃退火温度下的OM及SEM分析结果未见明显差别。于是使用分子动力学模拟对0Cr25Al5钢三元体系的自由能进行了计算,发现随着B2结构的FeAl或者DO3结构的Fe₃Al有序相尺寸的增大,系统自由能先减小后增大,其最小值随着退火温度的升高向有序相颗粒尺寸减小的方向移动。在1273 K的高温下仍然会保留60 nm左右大小的有序相颗粒。因此,推测0Cr25Al5钢在大于950 ℃的温度范围内韧性下降是由于60 nm左右的B2结构的FeAl或者DO3结构的Fe₃Al有序相造成,与晶粒尺寸无关。因此,针对该钢种应进行低温退火促使基体组织回复以消除缺陷,从而抑制Fe、Al等基体原子的扩散。     

生物质电厂废弃物草木灰成分分析及成形

生物质热电厂焚烧废弃物的主要成分是草木灰，其产生量大、密度小。大量草木灰不经处理会造成环境污染问题。本文首先分析草木灰的化学成分，确定草木灰的肥料特征，通过添加NH₄H₂PO₄使草木灰的pH达到国家复合肥的相关标准。选用聚天冬氨酸（30%水溶液）作为复合肥的黏结剂，应用于草木灰复合肥的成形造粒，以增加其抗压强度和肥效。研究不同烘干时间、烘干温度、聚天冬氨酸添加量对草木灰复合肥抗压强度的影响规律，通过分析植物的形态及生理指标，进而研究草木灰复合肥的肥效。结果表明：最佳烘干条件为10h、140℃，聚天冬氨酸对草木灰的抗压强度有明显的增强作用，并且草木灰与聚天冬氨酸的复配比为6g∶1mL时肥效最好。此方法解决了元素循环中断、草木灰环境污染，在运输过程中草木灰复合肥易碎，纯草木灰肥效低等问题。     

Effect of Temperature and Strain Rate on the Hot Deformation Behaviour of Ferritic Stainless Steel

Metals and Materials International - The flow behaviour and microstructure characteristics of a ferritic stainless steel were investigated using plain strain compression test on a Gleeble 3500...     

利用固液扩散偶研究Mg-40Al与Mg-20Ce的界面反应

本文主要研究了Mg-40Al与Mg-20Ce固液界面在475°C, 500°C和525°C下保温5min至30min的界面反应和扩散层的生长动力学。结果发现，在扩散层中由于Al元素和Ce元素反应生成Al₁₁Ce₃, Al₃Ce and Al₂Ce金属化合物。金属化合物的体积分数随着扩散温度的升高而增加。扩散层的生长满足抛物线生长规律，扩散层的扩散激活能为42±3.7kJ/mol。实验研究的固液扩散为理解合金熔炼过程中金属化合物的形成提供了理论基础。     

Supply chain network design under the risk of uncertain disruptions

Facility disruptions in the supply chain often lead to catastrophic consequences, although they occur rarely. The low frequency and non-repeatability of disruptive events also make it impossible to estimate the disruption probability accurately. Therefore, we construct an uncertain programming model to design the three-echelon supply chain network with the disruption risk, in which disruptions are considered as uncertain events. Under the constraint of satisfying customer demands, the model optimises the selection of retailers with uncertain disruptions and the assignment of customers and retailers, in order to minimise the expected total cost of network design. In addition, we simplify the proposed model by analysing its properties and further linearise the simplified model. A Lagrangian relaxation algorithm for the linearised model and a genetic algorithm for the simplified model are developed to solve medium-scale problems and large-scale problems, respectively. Finally, we illustrate the effectiveness of proposed models and algorithms through several numerical examples.     

海水淡化用空心锥喷嘴喷淋性能理论及实验研究

设计开发一种具有高通量、低流阻特征的空心锥喷嘴,并通过理论与实验方法研究空心锥喷嘴的喷淋性能,基于准自由涡理论建立空心锥喷嘴内部流体流动的数学模型,阐明流量系数、喷淋锥角、喷嘴流量与喷嘴结构参数之间的定量关系,并利用多效蒸馏海水淡化喷淋实验台对理论计算结果进行实验测试和验证。研究结果表明:正常工作状态下喷嘴流量系数、喷淋锥角、喷淋流量等参数理论值与测量值之间的误差小于5%,验证了设计模型的准确性。同时根据实验测试数据,拟合得到该类型空心锥喷嘴喷淋锥角与雷诺数之间的经验公式,可为蒸馏海水淡化用大流量空心锥喷嘴的结构设计、工艺选型提供理论指导和数据支持。     

An easy and scalable approach to synthesize three-dimensional sandwich-like Si/Polyaniline/Graphene nanoarchitecture anode for lithium ion batteries

A new three-dimensional (3D) sandwich-like Si/Polyaniline/Graphene nanoarchitecture anode for lithium ion batteries (LIBs) is successfully fabricated through an easy approach. In this nanoarchitecture, the in-situ polymerized electronic conductive polyaniline (PAni) hydrogel, acting as “glue”, agglutinates tightly to both the silicon nanoparticles (SiNPs) and graphene sheets, forming efficient conductive networks with high elastic modulus and high tensile strength. This mechanically robust nanoarchitecture can endure the great volume change of silicon and retain structural stability during Li-ion insertion/extraction. The electrodes consisting of this 3D sandwich-like Si/Polyaniline/Graphene nanoarchitecture reveal excellent electrochemical performance. The progress made in this work provides an easy and scalable route for preparing Si-based anode materials with high performance for advanced LIBs.